Değirmenci A, Bilgili CD

Language: English
References: 42
Page: 99-112
PDF size: 273.56 Kb.

ABSTRACT

The aim of this study was to investigate the effect of preheating three bulkfill and one conventional composite resin on the Vickers microhardness and depth of cure of these composites. In this study, three bulk-fill composites-SDR Plus (SDR), Estelite BULK FILL Flow (EST), Admira^® Fusion x-tra (AFX), and one conventional composite resin G-ænial POSTERIOR (GP) were used as the control group. The samples were obtained at room temperature (24°C) and at 55°C in T2 mode after being placed in a heating device for 10 minutes. The samples were divided into eight groups (n=10) according to the type of material and heating process that was utilized (preheated and nonheated). All samples were tested with a Vickers microhardness (VHN) tester on the bottom and top surfaces. The first measurements were obtained at baseline; the second set of measurements was performed after the samples were stored in distilled water at 37°C for 24 hours. The depth of cure was calculated using a bottom/ top hardness ratio of measurements. Statistical analysis was performed utilizing the SPSS V23 and Shapiro-Wilk tests. Lastly, the Duncan test was used for multiple comparisons (p‹0.05). While the VHN increased after the preheating procedure in bulk-fill composites, it decreased in GP. There was no difference between the baseline and the 24-hour VHN values in SDR and GP. After 24 hours, while the VHN of EST increased, the VHN of AFX decreased. There was no difference between the hardness ratios of the AFX and EST samples (p‹0.001) and hardness ratios were greater than GP and SDR. When comparing the baseline and the 24-hour values, the VHN depended on the type of materials. Sufficient curing depth was obtained in all groups with a thickness of 2mm.

REFERENCES

1. Ilie N., Hickel R. Resin composite restorative materials. Aust Dent J. 2011;56 Suppl 1: 59-66.

2. Cramer N.B., Stansbury J.W., Bowman C.N. Recent advances and developments in composite dental restorative materials. J Dent Res. 2011; 90 (4): 402-16.

3. Ferracane J.L. Current trends in dental composites. Crit Rev Oral Biol Med. 1995; 6 (4): 302-18.

4. Herrero A.A., Yaman P., Dennison J.B. Polymerization shrinkage and depth of cure of packable composites. Quintessence Int. 2005; 36 (1): 25-31.

5. Chikawa H., Inai N., Cho E., Kishikawa R., Otsuki M., Foxton R.M., et al. Effect of incremental filling technique on adhesion of light-cured resin composite to cavity floor. Dent Mater J. 2006; 25 (3): 503-8.

6. Peutzfeldt A., Asmussen E. Determinants of in vitro gap formation of resin composites. J Dent. 2004; 32 (2): 109-15.

7. Ilie N., Hickel R. Investigations on a methacrylate-based flowable composite based on the SDR technology. Dent Mater. 2011; 27 (4): 348-55.

8. Bilgili D., Dundar A., Barutcugil C., Tayfun D., Ozyurt O.K. Surface properties and bacterial adhesion of bulk-fill composite resins. J Dent. 2020; 95: 103317.

9. Bucuta S., Ilie N. Light transmittance and micro-mechanical properties of bulk fill vs. conventional resin based composites. Clin Oral Invest. 2014; 18 (8): 1991-2000.

10. Lima R.B.W., Troconis C.C.M., Moreno M.B.P., Murillo-Gómez F., De Goes M.F. Depth of cure of bulk fill resin composites: A systematic review. J Esthet Dent. 2018; 30 (6): 492-501.

11. Finan L., Palin W.M., Moskwa N., McGinley E.L., Fleming G.J. The influence of irradiation potential on the degree of conversion and mechanical properties of two bulk-fill flowable RBC base materials. Dent Mater. 2013; 29 (8): 906-12.

12. Fróes-Salgado N.R., Silva L.M., Kawano Y., Francci C., Reis A., Loguercio A.D. Composite pre-heating: effects on marginal adaptation, degree of conversion and mechanical properties. Dent Mater. 2010; 26 (9): 908-14.

13. Theodoridis M., Dionysopoulos D., Koliniotou- Koumpia E., Dionysopoulos P, Gerasimou P. Effect of preheating and shade on surface microhardness of silorane based composites. J Investig Clin Dent. 2017;8 (2): e12204.

14. Leprince J.G., Leveque P., Nysten B., Gallez B., Devaux J., Leloup G. New insight into the "depth of cure" of dimethacrylate-based dental composites. Dent Mater. 2012; 28 (5): 512-20.

15. Rodriguez A., Yaman P., Dennison J., Garcia D. Effect of Light-Curing Exposure Time, Shade, and Thickness on the Depth of Cure of Bulk Fill Composites. Oper Dent. 2017; 42 (5): 505-13.

16. Flury S., Hayoz S., Peutzfeldt A., Hüsler J., Lussi A. Depth of cure of resin composites: is the ISO 4049 method suitable for bulk fill materials? Dent Mater. 2012; 28 (5): 521-8.

17. Cohen V., Jellinek S.P., Teperikidis L., Berkovits E., Goldman W.M. Room-temperature storage of medications labeled for refrigeration. Am J Health Syst Pharm. 2007; 64 (16): 1711-5.

18. Ayub K.V., Santos G.C., Jr., Rizkalla A.S., Bohay R., Pegoraro L.F., Rubo J.H., et al. Effect of preheating on microhardness and viscosity of 4 resin composites. J Can Dent Assoc. 2014; 80: e12.

19. Nagi S.M., Moharam L.M., Zaazou M.H. Effect of resin thickness, and curing time on the micro-hardness of bulk-fill resin composites. J Clin Exp Dent. 2015;7 (5): e600-4.

20. Yan Y.L., Kim Y.K., Kim K.H., Kwon T.Y. Changes in degree of conversion and microhardness of dental resin cements. Oper Dent. 2010; 35 (2): 203-10.

21. Deb S., Di Silvio L., Mackler H.E., Millar B.J. Pre-warming of dental composites. Dent Mater. 2011; 27 (4): e51-9.

22. Daronch M., Rueggeberg F.A., De Goes M.F., Giudici R. Polymerization kinetics of pre-heated composite. J Dent Res. 2006; 85 (1): 38-43.

23. Lucey S., Lynch C.D., Ray N.J., Burke F.M., Hannigan A. Effect of pre-heating on the viscosity and microhardness of a resin composite. J Oral Rehabil. 2010; 37 (4): 278-82.

24. Daronch M., Rueggeberg F.A., De Goes M.F. Monomer conversion of pre-heated composite. J Dent Res. 2005; 84 (7): 663-7.

25. Eliades G.C., Vougiouklakis G.J., Caputo A.A. Degree of double bond conversion in light-cured composites. Dent Mater. 1987; 3 (1): 19-25.

26. Alshali R.Z., Salim N.A., Satterthwaite J.D., Silikas N. Post-irradiation hardness development, chemical softening, and thermal stability of bulk-fill and conventional resin-composites. J Dent. 2015; 43 (2): 209-18.

27. Monsarrat P., Garnier S., Vergnes J.N., Nasr K., Grosgogeat B., Joniot S. Survival of directly placed ormocer-based restorative materials: A systematic review and meta-analysis of clinical trials. Dent Mater. 2017; 33 (5): e212-e20.

28. Bottenberg P., Jacquet W., Alaerts M., Keulemans F. A prospective randomized clinical trial of one bis-GMA-based and two ormocer-based composite restorative systems in class II cavities: Five-year results. J Dent. 2009; 37 (3): 198-203.

29. Ilie N., Bucuta S., Draenert M. Bulk-fill resinbased composites: an in vitro assessment of their mechanical performance. Oper Dent. 2013; 38 (6): 618-25.

30. Kelić K., Matić S., Marović D., Klarić E., Tarle Z. Microhardness of Bulk-Fill Composite Materials. Acta Clin Croat. 2016; 55 (4): 607-14.

31. da Silva E.M., Poskus L.T., Guimarães J.G.A. Influence of light-polymerization modes on the degree of conversion and mechanical properties of resin composites: a comparative analysis between a hybrid and a nanofilled composite. Oper Dent. 2008; 33 (3): 287-93.

32. Lovelh L., Newman S., Bowman C. The effects of light intensity, temperature, and comonomer composition on the polymerization behavior of dimethacrylate dental resins. J Dent Res. 1999; 78 (8): 1469-76.

33. Alkhudhairy F.I. The effect of curing intensity on mechanical properties of different bulk-fill composite resins. Clin Cosmet Investig Dent. 2017; 9: 1.

34. Colombo M., Gallo S. New Resin-Based Bulk-Fill Composites: in vitro Evaluation of Micro-Hardness and Depth of Cure as Infection Risk Indexes. Materials (Basel). 2020; 13 (6).

35. Al-Ahdal K., Ilie N., Silikas N., Watts D.C. Polymerization kinetics and impact of post polymerization on the Degree of Conversion of bulk-fill resin-composite at clinically relevant depth. Dent Mater. 2015; 31 (10): 1207-13.

36. Shortall A.C., Palin W.M., Burtscher P. Refractive index mismatch and monomer reactivity influence composite curing depth. J Dent Res. 2008; 87 (1): 84-8.

37. Lee Y-K. Influence of filler on the difference between the transmitted and reflected colors of experimental resin composites. Dent Mater. 2008; 24 (9): 1243-7.

38. Mohamad D., Young R., Mann A., Watts D. Post-polymerization of dental resin composite evaluated with nanoindentation and micro-Raman spectroscopy. Arch Orofac Sci. 2007; 2: 26-31.

39. Leung R., Fan P., Johnston W. Post-irradiation polymerization of visible light-activated composite resin. J Dent Res. 1983; 62 (3): 363-5.

40. Tarumi H., Imazato S., Ehara A., Kato S., Ebi N., Ebisu S. Post-irradiation polymerization of composites containing bis-GMA and TEGDMA. Dent Mater. 1999; 15 (4): 238-42.

41. Daronch M., Rueggeberg F.A., Moss L., de Goes M.F. Clinically relevant issues related to preheating composites. J Esthet Restor Dent. 2006; 18 (6): 340-50; discussion 51.

42. Moharam L.M., El-Hoshy A.Z., Abou-Elenein K. The effect of different insertion techniques on the depth of cure and vickers surface microhardness of two bulk-fill resin composite materials. J Clin Exp Dent. 2017; 9 (2): e266-e71.